Available Specification & Application
|
 |
Specification |
T1, T2, T3, T4, T5 |
DR8, DR9, DR10 |
Sheets |
Coil |
Sheets |
Coil |
Thickness (mm) |
0.15 - 060 |
0.15 - 0.60 |
0.14 - 0.36 |
0.14 - 0.36 |
Width (mm) |
650 - 988 |
650 - 988 |
650 - 988 |
650 - 988 |
Length (mm) |
457 - 1200 |
|
457 - 1200 |
|
Inside Diameter (mm) |
|
406,508 |
|
406,508 |
Outside Diameter (mm) |
|
1725 |
|
1725 |
Weight (mtons) |
Max. 2 |
3 - 11 |
Max. 2 |
3 - 11 |
|

Note:
 |
● |
Certain combination of specification is subject to further verification. |
● |
For primary scroll , please contact us. |
|
|
|
|
Coating Weight
|
 |
Letter Symbol of Classification |
Type of Coating |
Designation of Coating Weight (g/m2) |
Nominal Coating Weight (g/m2) |
Minimum Average Coating Weight |
Coating Number (reference only) |
SPTE |
Equal Coated |
2.8 / 2.8
5.6 / 5.6
8.4 / 8.4
11.2 / 11.2 |
2.8 / 2.8
5.6 / 5.6
8.4 / 8.4
11.2 / 11.2 |
4.9
10.5
15.7
20.2 |
#25
#50
#75
#100 |
Differential Coated |
2.8 / 5.6
2.8 / 8.4
2.8 / 11.2
5.6 / 8.4
5.6 / 11.2
8.4 / 11.2 |
2.8 / 5.6
2.8 / 8.4
2.8 / 11.2
5.6 / 8.4
5.6 / 11.2
8.4 / 11.2 |
2.25 / 5.05
2.25 / 7.85
2.25 / 10.1
5.05 / 7.85
5.05 / 10.1
5.05 / 10.1 |
#25 / 50
#25 / 75
#25 / 100
#50 / 75
#50 / 100
#75 / 100 |
|

Note:
 |
● |
Coating weight in g/m2 corresponds to JIS G 3303 - 2008. |
● |
Value with slash (/) shows the coating weight on each respective surface,; values without slash (/) show the actual coating weight on both surfaces. |
● |
For coating weight not listed in table, please contact us. |
|
|
Designation and Marking for Differential Coating
|
 |
Type |
Designation of Coating Weight (g/m2) |
Differential Marking |
Parallel Lines on Heavier Side |
Edge Lines on Lighter Side |
Differentially Coated |
#25 / 50 (2.8 / 5.6)
#25 / 75 (2.8 / 8.4)
#25 / 100 (2.8 / 11.2)
#50 / 75 (5.6 / 8.4)
#50 / 100 (5.6 / 11.2) |
Line intervals of either 2" or 4" |
A line is marked within 10 mm from an edge. |
Examples of Markings |
|

Rolling Direction |

Rolling Direction |
|

Note:
 |
● |
If different marking is required, please inquired |
|
|
Temper
 |
Single - Reduce Tinplate
 |
Designation |
Aimed Rockwell
Hardness Range 30T |
Characterisic |
Application |
T - 1 |
46 - 52 |
Soft for drawing |
Nozzles, spouts, toys and other applications requiring extra deep drawing |
T - 2 |
50 - 56 |
Moderate drawing where some stiffness is required |
Rings and plugs, small-deformed cans, and other applications requiring moderately-deep drawing |
T - 2.5 |
52 - 58 |
Combines the characteristics of T - 2 and T - 3 |
Battery cells bodies, small can ends and bodies, and other applicaiton requiring moderately-deep drawing |
T - 3 |
54 - 60 |
Shallow drawing, general purpose with fair degree of stiffness to minimize fluting |
Can ends and bodies, large diameter closures, crown caps |
T - 4 |
58 - 64 |
Moderate stiffness |
Can ends and bodies where comparatively high strength is required |
T - 5 |
62 - 68 |
Increased stiffness to resist buckling |
Can ends and bodies where a combination of high hardness, strength and good formability is required |
|
|
Single - Reduce Tinplate
 |
Designation |
Aimed Rockwell
Hardness Range 30T |
Application |
DR - 8 |
68 - 78 |
Bodies and ends for small dimaters cans required high strength |
DR - 9 |
71 - 81 |
Bodies and ends for small dimaters cans required high strength |
DR - 10 |
75 - 85 |
Bodies and ends for small dimaters cans required high strength |
|
|
DR tinplate is thin, strong material developed as a substitute for ordinary tinplate to meet customer's requirements to reduce tinplate thickness |
|
|
Features
 |
● |
Stifness and strength are greater for same thickness of ordinary tinplate |
● |
Reduced thickness make it possible to increase the number of sheets per unit mass, and consequently reduce costs |
|
|
Finishes
 |
Code |
Classification |
Features |
B |
Bright |
A luster surface provided by a flow-brightened tin coating on a smooth grindstone finish stell base |
R |
Stone |
Melted finish. This finish has fine grit lines, and is easy to handle because it resists scratching during coating and can-making |
R2 |
Super Stone |
Melted finish. High resistance to scratching, thus making it asily handling during coating and can-making and is widely used for cna ends |
M |
Matte |
Unmelted dull finish. This finish gives the tinplate a unique silver gray surface. It oftens exceptional ink adherence and is widely used in crown caps and printed cans |
S |
Silver |
A luster surface provided by a flow-brightened tun coating on a coarse dull finished steel base |
|

Note:
 |
● |
Double reduced product is available in stone and super stone finish only |
|
|
|
|
Steel Types

|
Steel Types |
Remarks |
MR |
Contains low residual elements and has a good corrosion resistance. Commonly used for most tinplate applicaitons |
L |
Contain particularly low residual elements such as Cu, Ni, Cr and Mo and is used for improved corrosion resistance of certain food-product containers |
D |
Aluminium killed, is sometimes required for severe drawing applications or to minimize severe fluting and stretcher strain hazards |
|
|